Electric Circulation Heating Systems
3 KW, 6 KW, 11.5 KW
Circulation Heater
Contruction Features
- Incoloy steel heating elements
- Adjustable thermostat 60°F-107°F range (2 degree diff.) on 6 KW heater
- Adjustable thermostat 47°F-107°F range (4 degree diff.) on 11.5 KW heater
- Well insulated with fiberglass
- For use with 240V single phase power
- Can be used with 208 Voltage, but heating is reduced 25%
- Can be used with 120 Voltage, but heating is reduced 75%
- Little Giant pump is 1/40 H.P. - 120V. - circulated 600 GPH at 1-foot head
- Hi-Limit switch set at 118°F (± 4°)
Use the dimensions
illustrated to the right
with the table below
to identify the
Circulation Heater
that meets your need.
| Part Number | Model | Volts | Watts | "A" | "B" | "C" | Inlet or Outlet | Amps Drawn |
|---|---|---|---|---|---|---|---|---|
| 3HHL | 3 KW | 240 | 3000 | 22" | 16 3/8" | 5 1/2" | 1" F.S.P.S. | 12.5 amp |
| 6HHL | 6 KW | 240 | 6000 | 27" | 21 3/8" | 5 1/2" | 1" F.S.P.S. | 25 amp |
| 11.5HHL | 11.5 KW | 240 | 11,500 | 29 1/2" | 24 3/4" | 4 3/4" | 1" M.S.P.S. | 47.9 amp |
UL Recognition #E90821 (N)
3 KW Electric Circulation Heating System
3KW heats 45 gallons per hour - 30° Rise
List Price below with High Limit Protection
| Part No. | System Part Name | List Price |
|---|---|---|
| 3HHL | 3 KW Heater | $290.00 |
| P | Little Giant Pump No. 006 | $145.00 |
| PK | Pump Installation Kit | $55.00 |
| Total System Price | $490.00 |
6 KW Electric Circulation Heating System
6KW heats 90 gallons per hour - 30° Rise
List Price below with High Limit Protection
| Part No. | System Part Name | List Price |
|---|---|---|
| 6HHL | 6 KW Heater | $290.00 |
| P | Little Giant Pump No. 006 | $145.00 |
| PK | Pump Installation Kit | $55.00 |
| Total System Price | $490.00 |
11.5 KW Electric Circulation Heating System
11.5KW heats 115 gallons per hour - 30° Rise
List Price below with High Limit Protection
| Part No. | System Part Name | List Price |
|---|---|---|
| 11.5HHL | 11.5 KW Heater | $450.00 |
| P | Little Giant Pump No. 006 | $145.00 |
| PK | Pump Installation Kit | $55.00 |
| Total System Price | $650.00 |
Note: The 11.5 KW Heater Requires a 48 Amp Resistive Rating Contactor
and a 24V Transformer to operate.
Model #R8246A Contactor [Part No. CONT] List Price $60.00
Model #AT140A 24V Transformer [Part No. TR] List Price $30.00
| Ground Fault Interupter | $105.00 |
|---|
Low Water Protection For Heater And Pump
The #3000 Automatic System (listed below) will provide low water protection.
For Low Water Protection without #3000 Automatic System, order Low Water Protection [Part No. LWP]
List Price $90.00
Most churches select one of the following
Baptistry Heating Systems
| System Components | Part No. | 6 KW Heater | Part No. | 11.5 KW Heater |
|---|---|---|---|---|
| Little Giant Circulation Heater with Hi Limit | 6HHL | $290.00 | 11.5 HHL | $450.00 |
| #006 Little Giant Pump | P | $145.00 | P | $145.00 |
| Pump Installation Kit | PK | $55.00 | PK | $55.00 |
| #3000 Automatic System | 3000 | $190.00 | 3000 | $190.00 |
| #172 Trip Lever Drain Overflow | 172 D.3 for 3' Baptistry 172 D.4 for 4' Baptistry | $75.00 | 172 D.3 for 3' Baptistry 172 D.4 for 4' Baptistry | $75.00 |
| Total | $755.00 | Total | $915.00 |
Installation Instructions for 6 KW and 11.5 KW Little Giant Electric Circulation Water Heater and Pump
Gravity Circulation
Gravity Circulation is only recommended for the 3 KW Little Giant Heater. Higher KW heaters recover hot water too fast for Gravity Circulation. In addition, the water is delivered into the Baptistry at a high temperature so that manual stirring is normally required to mix the water. Also, the heater's thermostat cycles the heating element on and off. This shortens the thermostat's life; and due to the off time lengthens the heating time. Lime, magnesium and other minerals are deposited more readily with Gravity Circulation. However, an advantage of this system is that the cost of the pump and its operational cost is eliminated.
Pump Circulation
Circulation of water through the heater by pump is the best type Baptistry Heating System. The Baptistry water is heated uniformly without manual stirring. Minerals are not deposited as quickly because of the lower water temperature.
Installation
Assemble and make up tightly the complete heater and parts as shown (except slip joint nuts). Locate the most accessible place around the Baptistry for installation. Drill a 2-1/8" diameter hole 4-1/2" up from the Baptistry floor. Smooth hole and install chrome faced inlet flush port, by loosening at slip joint nut. Apply clear RTV sealant under chrome flange. Remove any outside insulation so port rubber gasket fits against outside of fiberglass wall. Measure center to center distance exactly between inlet and outlet fittings. Locate and drill a 2-1/8" hole for top port using method stated above.
Assemble complete heating system onto installed ports. Important - Block under heater or pump to support weight - this prevents leakage of Baptistry wall fittings.
Heaters are shipped with special Installation Instructions regarding wiring, etc.
Caution:
Be certain heater is turned off before draining Baptistry. Always fill Baptistry before turning heater on. Dry operation will burn out heating element, and cause failure of the pump.
Choosing a Baptistry
[ Baptistry Features ] [ Double Entry Baptistry ] [ Single Entry Baptistry ] [ Dry Area Access Baptistries ]
[ Baptistry Accessories ] [ Baptistry Heating ]
Choosing a Steeple
[ Most Popular Steeples ] [ Steeples over 40 feet ] [ Steeples 34 to 39 feet ] [ Steeples 20 to 32 feet ]
[ Embellished Steeples ] [ Cupolas over 10 feet ] [ Cupolas 3 to 9 feet ]
[ Tapered Wall Crosses ] [ Square Wall Crosses ]
Water Heating Solutions
[ Pools and Spas ] [ Carpet Cleaning ] [ Restaurant Applications ] [ Baptistry Heating ]
[ Electric Circulation ] [ Electric Immersion ] [ Hotomatic® Gas ]
[ Plumbing Contractors ] [ General Contractors ] [ Architects ] [ Church Building Committees ]
Copyright © 2002-2007 Little Giant Manufacturing Co., Inc.